Does a Focusrite Scarlett need drivers on a Mac, and how do you set it up?

No driver needed: the Scarlett Solo and 2i2 are class-compliant on macOS. Here is the setup chain for a speaking voice, what Focusrite Control 2 is for, and the fixes for the drive icon, the one-ear voice and silent apps.


A new Scarlett Solo comes out of the box, goes into the MacBook's USB-C port, and the first thing on screen is not a sound device. It is a drive on the desktop, as if someone had plugged in a memory stick. So the next move is a search for "Focusrite Scarlett Solo driver", a download page, and twenty minutes of looking for an installer that does not exist for the Mac. Then the Zoom call starts, the ring around the gain knob glows green, and the colleague on the other end says your voice is only in their right ear. Or that they hear nothing at all.

None of that is a missing driver. Each symptom has its own cause, and most of them take one click to fix once you know which click. This guide covers what the Mac needs (almost nothing), what the optional Focusrite app does, how to set up a Scarlett Solo or 2i2 for a speaking voice, and the Mac problems people hit most often, with the exact fix for each.

Does a Focusrite Scarlett need drivers on a Mac?

No. Focusrite's own document for the Mac is titled "No Driver Required": the Scarlett is a class-compliant USB audio device, so macOS talks to it with the audio support built into the system. You plug it in, choose it as the input in System Settings and in your app, and it works. That holds for the Scarlett Solo and the 2i2 in every generation. If you came looking for a Scarlett 2i2 driver or a Scarlett Solo driver for macOS, there is nothing to download.

Focusrite's macOS compatibility page, as of October 2026, lists the Scarlett 4th Gen, 3rd Gen, 2nd Gen and the 1st Gen Solo and 2i2 as compatible with macOS 26 Tahoe on both Intel and Apple silicon Macs. The same page asks people not to upgrade macOS in the middle of a time-critical project and suggests waiting a few months after a major macOS release. That advice is worth more than any driver hunt.

The one thing you might install is Focusrite Control 2, a free app. It is not a driver on the Mac. It mirrors the front-panel buttons on screen, sets the direct monitor mix, updates the interface firmware and switches off the drive-like "Easy Start" mode described below. Focusrite's release notes list macOS 14 Sonoma, 15 Sequoia and 26 Tahoe as supported, and both the 4th Gen and 3rd Gen Scarlett as supported devices. If an older Mac still has the original Focusrite Control on it, Focusrite says to uninstall that first.

If you have not bought the interface yet and are stuck between the two small models, the page you want is Focusrite Scarlett Solo or 2i2, which one do you need for your mic?. If you are not sure you need an interface at all, because a USB mic might cover your calls, read Do you need an audio interface for a microphone on a Mac? first. This page assumes the Scarlett is already on your desk.

Why your Scarlett shows up as a drive

On first connection, 3rd Gen and 4th Gen Scarletts appear on the Mac as a Mass Storage Device. Focusrite calls this Easy Start mode. Inside the drive is a link, "Click Here to Get Started", that opens a registration and setup page in the browser. Nothing is broken, and you do not need to register to use the interface.

Easy Start has one real side effect: in this mode the interface runs at sample rates up to 48 kHz only. For calls and voice work 48 kHz is the normal rate anyway, but it explains why 96 kHz is unavailable in a recording app or in the Format menu of Audio MIDI Setup.

There are two ways out:

  1. Install and open Focusrite Control 2. On the 4th Gen, opening it disables Easy Start and offers a firmware update. Keep the Scarlett connected until the update finishes.
  2. On a 3rd Gen, skip the app. Focusrite's 3rd Gen guide says to hold the 48V button for five seconds with the interface connected. Before you do that, unplug any condenser mic or turn its gain down, because 48V is phantom power and you are pressing the real button.

After either step the drive stops appearing.

What each generation needs on a Mac

Scarlett 4th Gen (Solo, 2i2)Scarlett 3rd Gen (Solo, 2i2)Older Scarlett Solo and 2i2
Driver on macOSNone, class-compliantNone, class-compliantNone, class-compliant
Listed for macOS 26 TahoeYes, Intel and Apple siliconYes, Intel and Apple siliconYes (2nd and 1st Gen)
First connectionEasy Start driveEasy Start drivePlain audio device
Optional appFocusrite Control 2Focusrite Control 2Not needed for basic use
Mic gain rangeSolo 57 dB, 2i2 69 dB56 dBSee the model's manual
Solo: mic arrives onInput 2Input 1Check the input labels

The last row causes more confusion on calls than everything else in this table, and it gets its own section below.

Focusrite Scarlett Solo setup on a Mac, step by step

Here is the full chain for one microphone and one voice. It is the same on a MacBook, an iMac or a Mac mini.

1. Gain knob for the mic input fully down (counterclockwise).
2. Mic on an XLR cable into the XLR socket on the back.
3. Scarlett into the Mac with the USB-C cable from the box, no hub.
   4th Gen USB LED: green = recognized, white = connected but not recognized.
4. Laptop with Apple silicon: if macOS asks to allow the accessory, click Allow.
5. Condenser mic: press 48V. Dynamic mic: leave 48V off.
6. Apple menu > System Settings > Sound > Input > choose the Scarlett.
7. Speak at your real distance and raise the gain until loud words
   reach about -12 dBFS. The halo should stay green, amber only on shouts.
8. In Zoom, Meet, Telegram, Discord or OBS, pick the Scarlett as the mic.
9. Solo 4th Gen used in a call or stream app: turn on Combine Input 1 and Input 2
   (hold Direct for three seconds), so the mic is heard in both ears.

Step 4 is new to many people. Mac laptops with Apple silicon ask before a new USB accessory may connect. If you clicked Don't Allow, the Mac will not recognize the Scarlett until you plug it in again and allow it, or change "Allow accessories to connect" in System Settings > Privacy & Security.

Step 7 is the one that decides how you sound. A level set too low gets raised later by the call app or by you, and the hiss of the preamp comes up with it. A level set too high clips, and a clipped word cannot be repaired. Our guide on gain staging explains the numbers in more depth. For where the macOS input settings live and what the input volume slider does with an interface, see How do you change microphone settings on a Mac?.

How to use a Scarlett 2i2 on a Mac: what changes

The 2i2 has two combo inputs, and each accepts an XLR plug or a 1/4" jack. Three details trip people up:

  • On the 2i2 4th Gen, the 48V button feeds both inputs at once. There is no per-channel switch. Focusrite says phantom power will not damage most modern microphones but may damage some older ones, so check the manual of any vintage mic before you switch 48V on for a condenser in the other input.
  • A jack disables the mic on that channel. On the 4th Gen, plugging a cable into a front jack cuts the XLR input of the same channel. If the mic on input 1 goes silent, look for a guitar lead still sitting in the front socket.
  • Full mic gain only comes through the XLR pins. Focusrite's 3rd Gen guide says a mic plugged in with a jack plug gets the reduced gain of the line input, which is likely too little for a microphone.

The 2i2 4th Gen also has Auto Gain: press Auto, talk normally through the ten-second countdown, and the interface sets the level. For one speaking voice it replaces step 7 above. Clip Safe pulls the gain down when a peak is about to clip, which matters more for a podcast laugh than for a calm meeting.

One more difference: on a 2i2 the mic usually goes into input 1, the left channel. Apps that take only the first input will hear it. Apps that take both inputs as a stereo pair will place it in the left ear. That is the most common call problem with any Scarlett, and it has its own section below.

Gain and Air: settings for a speaking voice

There is no universal knob position, because a quiet dynamic mic and a hot condenser need very different gain for the same voice. The target is a level, not a number on the dial.

Mic48VWhere the gain ends upAir
Condenser (for example an Audio-Technica AT2020 XLR)OnWell below maximum, peaks around -12 dBFSTry Presence, keep it off if sibilance gets sharp
Ordinary dynamic used close (SM58 type)OffHigher on the dial, still short of the stopPresence can help a dull mic
Low-output dynamic (Shure SM7B)OffNear or at the end of the Solo's 57 dBGain first, Air does not add level

Shure says the SM7B likes around 60 dB of clean gain. A Solo tops out at 57 dB and a 3rd Gen at 56 dB, so with that mic at a normal talking distance the knob runs out before the level is right. The 2i2 4th Gen has 69 dB. The other route is an inline booster, which Do you need a Cloudlifter or FetHead for a dynamic mic? covers.

Air on the 4th Gen has two modes. Press once for Air Presence, an analog boost of the upper range. Press again for Presence plus Harmonic Drive, which adds harmonics on top, and a third press turns it off. On the Solo, Air works only on the mic input, and Presence plus Drive only up to 96 kHz. On the 2i2 4th Gen, Air also works on the line and instrument inputs. On a calm, close voice Presence can add a little clarity. On a bright condenser in a bare room it can make the "s" sounds sharper. Listen on headphones with Direct monitor on and decide by ear.

Choosing the input: the one-ear problem on calls

Here is the cause of "they only hear me in one ear". A Scarlett presents itself to the Mac as a two-channel input. Many call and stream apps treat those two channels as left and right. With one mic, all the voice sits in one channel, so the listener hears it on one side.

On the Solo 4th Gen the trap is deeper. The mic is wired to Input 2, the instrument jack is Input 1. Focusrite's support article says some apps accept only the first input, so they get the empty instrument channel and the mic seems dead, even while the halo glows green. Apps that accept both put the mic in the right ear.

Focusrite's fix is a setting called Combine Input 1 and Input 2:

  • In Focusrite Control 2: Preferences > Device tab > tick Combine Input 1 and Input 2.
  • On the hardware: hold the Direct button for three seconds. Both channel number LEDs turn green while it is on.

With it on, both inputs are summed and the voice comes out of both sides. Focusrite recommends turning it off again when you record in a DAW, where you can pick the input channel yourself.

OBS has its own fix: Edit > Advanced Audio Properties and tick the mono option for the mic source (the OBS guide calls it downmix to mono), so a single-channel source plays in both channels. Our guide to OBS audio settings on a Mac walks through the rest of that window.

Focusrite Scarlett 2i2 Mac problems and their fixes

Most Scarlett problems on a Mac come down to the same handful of causes. Find the symptom, then work across.

SymptomLikely causeFix
Scarlett not in Sound settings, USB LED whiteNot recognized: cable, port or accessory promptOriginal cable, port on the Mac itself, allow the accessory, then install Focusrite Control 2 if it is still white
USB LED flashes red (Solo 4th Gen)Not enough USB powerThe Solo needs 900 mA. Plug straight into the Mac, no hub
A drive called Scarlett appearsEasy Start modeOpen Focusrite Control 2. On a 3rd Gen you can also hold 48V for five seconds
Halo moves, app shows no levelApp has no microphone permissionSystem Settings > Privacy & Security > Microphone, switch the app on
Voice only in one earTwo-channel input, one micCombine Input 1 and Input 2 on the Solo 4th Gen, mono in OBS
Solo 4th Gen dead in one app, fine in anotherApp reads only Input 1Combine Input 1 and Input 2
Both tracks in Logic or GarageBand record input 1, or the voice sounds processedVoice Isolation mic modeControl Center > Mic Mode > Standard
You hear yourself twice, slightly delayedDirect monitor plus software monitoringKeep one: Direct on the Scarlett, or monitoring in the app
96 kHz unavailableStill in Easy StartLeave Easy Start, or stay at 48 kHz for voice
Quiet even at full gainLow-output dynamic mic2i2 4th Gen, an inline booster, or a hotter mic

Two rows need a little more explanation.

Microphone permission. Focusrite points out that the macOS microphone setting, despite its name, controls access to every audio input, including the Scarlett. If you once clicked Don't Allow when Zoom, Telegram or your recorder asked for the microphone, that app hears silence from the interface even though every light on it says signal. On macOS 13 Ventura and later the switch is in System Settings > Privacy & Security > Microphone.

Voice Isolation. When an app that supports it is using the mic, macOS offers a Mic Mode menu in Control Center: Standard, Voice Isolation, sometimes Wide Spectrum. Focusrite's article on Sonoma, Sequoia and Tahoe recommends Standard for its interfaces. With Voice Isolation on, the Mac sends input 1 to every track, the processing is built for speech only, and on a Solo 4th Gen it needs the combined inputs to work at all. If you want noise removal on calls, it is a valid choice. Just know that it changes the sound coming off the Scarlett, and switch back to Standard when you record.

If the Scarlett still does not appear after all this, our general checklist in Why is your Mac microphone not working? covers the macOS side, including resetting the audio settings.

What the Scarlett does and does not do for your voice

Once everything above is right, the Scarlett is doing its whole job: clean gain, phantom power, the analog-to-digital conversion, headphone monitoring with no delay. That is the foundation, and no software makes up for a wrong gain setting or a mic in the wrong channel.

What the interface does not do is fit the sound to your voice and your room. Air is a fixed curve, identical for a deep voice and a bright one. The interface does not touch the hum of the air conditioner, the fan in the laptop, or the echo of a bare room. Call apps may then add their own noise suppression on top, and none of it is set to your particular voice.

That gap is where TunedMic fits, if you are on a Mac. The app adds a virtual microphone to macOS, also called TunedMic. It takes the sound from the Scarlett, processes it on the Mac in real time, and any app that lets you choose a mic can pick TunedMic instead of the Scarlett: Zoom, Meet, Teams, Telegram, Discord, OBS, FaceTime. Setup is a one-minute Sound Check: you read a short passage aloud, and TunedMic takes more than 30 measurements of your voice, your mic and your room. From that it builds nine profiles in three families, for calls, for streams and podcasts, and for singing. It adds less than a tenth of a second of delay and runs locally, so the voice never leaves the Mac.

The order matters. Get the Scarlett right first: channel, permission, Mic Mode Standard, peaks near -12 dBFS. TunedMic works with what the interface sends it. And check the limits before you count on it: TunedMic needs a Mac with Apple silicon (M1 or newer) and macOS 14 or later. Intel Macs are not supported and there is no Windows version, even though the Scarlett itself runs on both.

Your next step

Plug in the Scarlett, open System Settings > Sound > Input, and talk. If the level moves there but your call app hears nothing or only one side, the fix is in the table above, not in a driver. Set Mic Mode to Standard, turn on Combine Input 1 and Input 2 if you have a Solo 4th Gen, and set the gain for peaks near -12 dBFS.

When the level is right and the voice still sounds thin, boomy or roomy on the call, that is a tone problem. Watch the 38-second video on the home page with the sound on: it shows the one-minute read-aloud that tunes the mic to your voice, and the Speech Report you get after a call. Then run the Sound Check on your own Scarlett: the free trial lasts 7 days from the first launch, includes every feature and needs no card or account. The price after that is on the pricing page.

Keep reading