Do you need a shock mount for your microphone?

A shock mount stops thumps that travel through the desk and stand, not key clicks, fans or echo. When you need one, when your mic already has one inside, and which mount fits the Yeti, QuadCast, Wave:3, NT1 and others.


You are on a Zoom call taking notes while someone else talks. Your condenser mic sits on its little tripod six inches from the keyboard. Every time you hit the space bar, the other side hears a soft, low thud, like someone knocking on a door two rooms away. Then you set your mug down and they hear a bang. Nobody says anything, but the speaker pauses for half a second each time.

That thud is the problem a shock mount exists for. It is also the only one. A shock mount will not touch the click of the keys, the hum of the fridge or the echo of a bare room, and plenty of people buy one hoping it will. So the honest answer to "do I need a shock mount" is: it depends on which of those sounds you are actually hearing, and on whether your mic already has one inside it.

What a shock mount actually stops

Sound reaches a microphone by two roads. One is through the air: your voice, the keyboard clicks, the fan, the dog. The other is through solid things: the desk, the stand, the arm, the cable. A microphone capsule is a thin diaphragm on a body, and when the body itself moves, the diaphragm moves relative to it. Wikipedia's article on shock mounts puts it neatly: microphones "behave to some extent as accelerometers". Shake the body and the capsule reports it as sound.

What comes through the structure is mostly low frequency. A knuckle on the desk, a foot tapping the floor under a floor stand, the arm creaking as you nudge it, a laptop lid closing. On a recording these show up as thumps and rumble rather than as clean, recognisable sounds, because the desk and stand only carry the heavy, slow part of the vibration well.

A shock mount breaks that second road. The mic hangs in elastic bands, a rubber suspension or a set of flexible plastic arms, so the stand can shake while the mic stays still.

Noise you hearHow it reaches the micDoes a shock mount help?
Thud when you hit the space bar or rest your wrist on the deskThrough the desk and standYes
Bang when you put a mug or phone downThrough the desk and standYes
Rumble from footsteps on a wooden floor (floor stand)Through the floor and standYes
Creak or knock when you move the mic or the armThrough the arm and mountYes, partly
Click of the keys themselvesThrough the airNo
Fan, fridge, traffic, a hair dryer next doorThrough the airNo
Room echo, a hollow "bathroom" soundThrough the air, bounced off wallsNo
Hiss, static, buzzElectricalNo

Many desk setups have a mix: the thud from the desk and the clicks through the air. The mount fixes one half. If the thud is what makes the people on your call wince, that is the half worth fixing.

Why a cheap mount can make things worse

A suspension is a spring with a weight on it, and every spring and weight has a natural frequency. The physics is simple and unforgiving. Well below that frequency, vibration passes straight through as if the mount were not there. Right at it, the vibration is amplified, because the mic starts bouncing on its elastics. Only above it does the mount actually isolate, and the lower the natural frequency, the more it isolates.

In practice this means three things. Tight, stiff elastics on a light mic push the natural frequency up and isolate less. Worn, slack elastics let a heavy mic sag until it touches the frame, at which point there is no isolation at all. And a mount that wobbles for a second after you touch it is a mount working near resonance. A good one stops moving quickly.

When you do not need one

Before you buy anything, check what you already have. Several popular mics already carry an internal suspension, and putting a second one around them changes little.

If your mic shares the desk you type on and you are wondering whether to get it off that desk entirely, read whether you need a boom arm, and which kind instead: moving the mic away from the source of the thumps often solves more than suspending it does.

You can skip the shock mount if:

  • Your mic has internal isolation. The Shure SM7B has what Shure calls internal "air suspension" shock isolation that "virtually eliminates mechanical noise transmission". The Rode PodMic and PodMic USB have an internal shockmount, according to Rode. The Blue Yeti, now sold by Logitech G, has an internal shockmount that "protects the 3-capsule array". The HyperX SoloCast 2 lists an internal shock mount as well.
  • Your mic is on your body. Headsets, lavaliers, AirPods and wireless clip-on mics move with you. A desk thump barely reaches them, and a shock mount does not apply. Clothing rustle on a lav is a different problem.
  • Your noise is airborne. If the recording has key clicks, fan hum or echo but no thuds, a mount buys you nothing. The fix is distance, direction and processing, covered in how to stop your mic from picking up background noise.
  • Nothing you touch shares furniture with the mic. If you record standing, with the mic on its own stand on a solid floor, and your hands stay off that stand, there is no thump to isolate.

When it earns its place

A shock mount pays for itself in a handful of setups, and they share one feature: the mic and something that moves are bolted to the same piece of furniture.

  1. A condenser mic on a desk stand next to your keyboard. This is the classic case. Condensers are sensitive by design, desk stands are rigid metal, and your hands are on the desk all day.
  2. A boom arm clamped to the desk you type on. An arm is a long lever. It carries vibration from the clamp to the mic very efficiently, and the springs in a typical arm can ring when knocked. A mount at the end of the arm breaks that path.
  3. A floor stand on a wooden or laminate floor. Footsteps, a rolling chair and a tapping foot all travel up a floor stand.
  4. You adjust the mic while live. If you tilt or swivel the mic during a stream, a suspension soaks up much of the handling noise that would otherwise go straight into the capsule.
  5. A large-diaphragm studio condenser. These are usually designed to live in a suspension, and many ship with one.

Will it fit your mic?

Fit is where a shock mount purchase usually goes wrong. Shock mounts are either made for one mic body or "universal" within a diameter range, and the thread at the bottom has to match your stand or arm.

Here is what the makers of popular mics say about isolation and matching mounts, as of October 2026. Prices are from the vendors' own US stores where they list one.

MicIsolation built in?Matching external mountNotes
Blue Yeti (Logitech G)Internal shockmountRadius III, $49.99Radius III is made for Yeti and Yeti family USB mics
HyperX QuadCast 2Detachable shock mount, pre-attachedUniversal mounts for a 55 mm bodySpring-loaded pins; joint fits 3/8 and 5/8 inch
HyperX QuadCast SBuilt-in elastic suspensionNot neededHyperX calls it an anti-vibration shock mount
Elgato Wave:3No mount in the boxWave Shock Mount, $39.99Also fits Wave:1; fits Wave:3 MK.1 and MK.2
Audio-Technica AT2020USB-XNoAT8455 (optional)Listed by Audio-Technica as the optional mount
Rode NT1 5th GenShock mount and pop filter in the boxIncludedRode's SM6 serves its large-diaphragm condensers
Rode Procaster / PodcasterNoRode PSM1Rode built the PSM1 for these two
Rode PodMic / PodMic USBInternal shockmountNot needed
Shure SM7BInternal air suspensionNot neededUses a 5/8 inch swivel
Samson Q2UNoSamson SP05, $12.99
Fifine K688Round shock mount with the base K688IncludedOther bundles pair it with stands or arms; check the listing
Tonor TC-777Mini shock mount in the boxIncludedFits 5/8 inch; 3/8 needs an adapter

Measuring for a universal mount

If your mic is not on a list like this, measure the body with a ruler at the point where the mount would grip it. Universal mounts state a range: the Rycote InVision USM, a well-known universal studio mount, takes mics from 18 to 55 mm across and up to 300 mm long, according to the retailer listing. A mic at the very top or bottom of a range tends to sit badly. Weight matters too: a heavy mic in a mount made for small ones sags against the frame.

Two more checks before you pay:

  • Side-address or end-address. A side-address mic (you talk into its side, like most large condensers and many USB mics) needs a cradle that leaves the front open. An end-address broadcast mic (you talk into its tip) needs a mount that grips the body without covering the grille.
  • Thread. Most US stands and arms use 5/8 inch, many European stands use 3/8 inch. Shure, for one, lists an adapter for 3/8 inch European stands in its spec sheets. A brass adapter costs almost nothing and saves a return. The desk mic stand guide covers which stands use which.

Setting it up so it actually isolates

A carelessly assembled shock mount leaks vibration through a side door. Four assembly details matter more than the brand, and the fifth line is the test that tells you whether you got them right.

SHOCK MOUNT CHECKLIST
1. Mic centred in the cradle, not touching the frame anywhere
2. Elastics even, no band twisted, none slack or snapped
3. Cable: leave a loose loop of 10 to 15 cm between mic and stand,
   then fix the cable to the stand or arm below the mount
4. Swivel and arm joints tight, so the mount itself does not rattle
5. Tap the desk with a knuckle while recording: you should hear
   much less thump than before, and no ringing after the tap

The cable is the step people skip. A tight USB or XLR cable running straight from the mic down the stand is a solid bridge around the suspension, and the thump walks across it. A slack loop has no tension to carry vibration.

Pop filters are a separate job. A pop filter stops bursts of air from "p" and "b" sounds; a shock mount stops vibration from the stand. Some mounts, like Rode's SM6, come with a pop shield attached, which is convenient but not the same thing. If plosives are the problem, read do you need a pop filter, or is a foam windscreen enough?

Free fixes before you buy

If the thump is mild, try these first. They cost nothing and some work better than a mount.

  • Move the mic to a different surface. A small side table, a shelf, a stand on the floor beside the desk. Breaking contact with the desk you type on breaks the main road.
  • Put something soft under the desk stand. A folded towel or a mouse mat under the base absorbs some of the knock. It is cruder than a suspension but helps with sharp taps.
  • Use a high-pass filter. Most structure-borne noise sits well below the voice. The SM7B has a bass roll-off switch for exactly this. For recordings, Audacity has one under Effect, then EQ and Filters, then High-Pass Filter, where you set the cutoff in hertz and the slope in decibels per octave. A cutoff around 80 Hz leaves most speaking voices intact and takes the floor out of the thumps.
  • Change your habits. Type with a lighter touch during calls, set the mug down on a coaster on another surface, and do not rest your forearms on the desk next to the stand.

A filter is not a cure. A thump has a sharp start that contains higher frequencies too, so a high-pass filter turns a boom into a tap rather than removing it.

Where software fits, and where it does not

No software can stop a vibration from reaching the capsule. Once the thud is in the signal, everything downstream is damage control. That is why the mechanical fix comes first if desk thumps are your problem.

What software can do is everything after that: the room, the steady background, the tone of your voice. On a Mac, TunedMic adds a virtual microphone that sits between your real mic and every app. You read a short passage aloud for about a minute in its Sound Check, TunedMic takes more than 30 measurements of your voice, your mic and your room, and builds a profile from them. Zoom, Google Meet, Teams, Discord or OBS then pick "TunedMic" as their mic and get the processed voice.

It has optional controls for noise, room echo, clarity and loudness, plus a 12-band equaliser, so you can turn the lowest bands down if a little rumble still gets through after you fix the mount. It does not remove all noise and it will not make a desk thump disappear; it treats the airborne half of the table above. What the setup looks like is in the 38-second video on the home page: a minute of reading aloud, then the same mic in Zoom, Google Meet or Discord.

The limits: TunedMic needs a Mac with Apple silicon (M1 or newer) and macOS 14 or later. There is no Windows version and no Intel support. It costs $19 once, with a free 7-day trial that starts at first launch and needs no card or account. Payments are final and there are no refunds, so use the trial to decide.

A sensible order for a desk setup looks like this:

StepWhat it fixesCost
Move the mic off the typing desk, or onto an armThumps, keyboard proximityFree, or the price of an arm
Shock mount, fitted and with a cable loopRemaining thumps through the stand$12.99 to $49.99 for the priced vendor mounts above
Pop filter or foamPlosivesSmall
High-pass filterLow rumble that still leaksFree
Processing such as TunedMicBackground noise, room echo, voice tone$19 once, after a 7-day trial

Your next step

Record a 20-second test tonight. Open QuickTime Player, choose File, then New Audio Recording, pick your usual mic from the pop-up menu next to the record button, then talk normally while you type a sentence, tap the desk once with a knuckle, and set a mug down. Listen back on headphones.

If you hear the knuckle and the mug as low thumps, a shock mount (or a move off the desk) is your fix. Check the table above for the mount made for your mic, or measure the body and buy a universal one in range. If what you hear is the key clicks, the fan and a hollow room, a shock mount will not help, and the free 7-day trial on your own mic is the way to judge whether processing on your Mac will.

Keep reading