Can a Rode VideoMic work as a microphone for your Mac?
Only two VideoMics, the NTG and the GO II, are USB mics a Mac sees without drivers. The Pro, Pro+ and VideoMicro II need an interface or an adapter. Model by model, with October 2026 prices and a call setup.
The shoot is over, the camera goes back in its bag, and the VideoMic Pro+ stays on the desk. Tomorrow at nine there is a Zoom call, and the mic that made your last video sound clean seems like the obvious upgrade over the MacBook's built-in one. You plug a cable from its USB port into the Mac. The battery light comes on. Zoom's microphone list stays exactly the same.
Nothing is broken. On the VideoMic Pro+ that port only carries power. Whether a Rode VideoMic can work as a Mac microphone depends entirely on which VideoMic you own, and the line splits cleanly in two. A couple of current models are full USB microphones the Mac sees with no drivers. The rest are analogue camera mics with a 3.5 mm plug, and they reach a Mac only through a small interface or an adapter cable.
This article goes model by model through the VideoMic range as RØDE sells it in October 2026: what connects how, what it costs, what extra cable or box you need, and what a camera shotgun actually gives you on a call. If you have not bought anything yet and simply want the right mic for filming yourself, our guide to the best microphone for YouTube videos is the page for you; it compares on-camera mics with desk and clip-on options. This one is for the person holding a VideoMic, or about to buy one, and wondering whether it can do double duty on a Mac.
Which Rode VideoMic models connect to a Mac
Here is the whole range, with the output RØDE lists for each model and the US price on RØDE's own site as of October 2026. Several of these pages, the NTG and Pro+ among them, send you to a dealer instead of a checkout, and prices in other countries and at other shops differ.
| Model | Output | Power | US price on rode.com (Oct 2026) | How it reaches a Mac |
|---|---|---|---|---|
| VideoMic NTG | 3.5 mm auto-sensing + USB-C digital | Built-in Li-ion, 30+ h | $259 | USB-C cable, no drivers |
| VideoMic GO II | 3.5 mm TRS + USB-C digital | Plug-in power or USB, no battery | $109 | USB-C cable, sold separately |
| VideoMic Pro+ | 3.5 mm TRS only | LB-1 battery, AA or micro-USB | $309 | Interface or TRS-to-TRRS adapter |
| VideoMic Pro | 3.5 mm TRS only | 9 V battery, 70+ h | $239 | Interface or adapter |
| VideoMic (Rycote) | 3.5 mm TRS only | 9 V battery | $159 | Interface or adapter |
| VideoMicro II | 3.5 mm TRS only | Plug-in power, no battery | $89 | Interface that supplies plug-in power |
| VideoMic GO (original) | 3.5 mm TRS | Plug-in power | Legacy product | Interface that supplies plug-in power |
| VideoMic Me-L | Lightning | From the iPhone | $59 | Not for Macs |
Two rows matter most for a Mac owner: the NTG and the GO II. They are the only VideoMics with a digital USB-C output, which means the analogue-to-digital conversion happens inside the mic and the Mac receives a finished 24-bit, 48 kHz signal. Everything else in the table puts out an analogue signal that something on the Mac side has to amplify and convert.
The VideoMic Pro gets more searches than any other model, which is bad luck for Mac owners: the Pro and Pro+ are the two best-known VideoMics, and neither has a USB audio output.
VideoMic NTG: the one that is already a USB mic
RØDE sells the VideoMic NTG as a camera shotgun that doubles as a desktop USB mic, and the spec sheet backs that up. It is class-compliant, so the Mac needs no driver: plug in the right-angle USB-C cable from the box and "VideoMic NTG" appears in System Settings > Sound > Input. RØDE lists macOS 10.12 as the minimum, which every Apple silicon Mac clears.
What the NTG brings to a desk:
- Gain on the mic itself. A stepless knob, numbered 1 to 15. RØDE says the output at 10 roughly matches the VideoMic Pro+, and suggests starting there.
- High-pass filter at 75 Hz or 150 Hz, switched by a button. The 75 Hz step is the useful one for calls: it trims desk thumps and air-conditioner rumble without thinning a voice.
- A -20 dB pad and a peak LED. If the LED flashes red while you talk, the mic's own preamp is clipping and the pad goes on.
- A headphone output. In USB mode the 3.5 mm jack becomes a headphone output, so you can hear yourself through the mic with no delay.
- A battery that charges from the Mac. 350 mAh, rated for 30+ hours, and the LED shows blue while it charges from a computer.
One thing catches people out. Because the NTG also has a headphone output, macOS lists it as an output device too, and RØDE's guide tells you to select it as both input and output. That is right only if your headphones are plugged into the mic. If they are not and the call suddenly goes silent, open System Settings > Sound > Output and pick the headphones or speakers you actually listen on.
The NTG's auto-sensing 3.5 mm output can also go into a Mac's headphone jack with the TRRS cable in the box. There is little reason to do that when USB is right there: USB skips the Mac's analogue input entirely and gives you the mic's own converter.
VideoMic GO II: USB on a budget, with one catch in the box
The VideoMic GO II is the cheapest way to get a VideoMic that a Mac sees as a USB microphone: $109 on RØDE's US store page in October 2026. RØDE says it uses the same annular line tube design as the NTG. It has a supercardioid pattern, 15 dBA of self-noise on paper, and a USB-C output that is class-compliant like the NTG's. RØDE lists macOS 10.15 as the minimum.
The catch: the GO II comes with a 3.5 mm patch cable for cameras, not a USB cable. RØDE's own page says you need an SC16 or SC17 (USB-C to USB-C) or an SC18 (USB-C to USB-A), sold separately. If you reach for a cable from the drawer instead, make sure it is a data cable: a charge-only cable carries power but no data, and the Mac will see no microphone.
The other details from RØDE's user guide that matter on a Mac:
- The GO II has no battery. It runs on power from whatever it is plugged into, so on USB the Mac powers it.
- The high-pass filter (75 or 150 Hz), the high-frequency boost and the -20 dB pad exist only in USB mode, and only through the free RØDE Central app (macOS 11 or later). There are no switches on the mic.
- The 3.5 mm jack turns into a headphone output in USB mode, just like on the NTG.
- RØDE recommends the foam windshield and the pad when you speak close to the mic, for plosives and for headroom.
For a Mac-first buyer who also wants a camera mic, the GO II is the sensible VideoMic. You give up the NTG's knob, buttons and battery, and you keep the USB output that makes the Mac part easy.
VideoMic Pro and Pro+: excellent on a camera, analogue on a Mac
The two most searched VideoMics, the Pro and the Pro+, are both analogue. RØDE lists the Pro+ output as "Minijack / 3.5mm TRS" and its power as the LB-1 battery or micro-USB. That micro-USB socket is the one from the opening scene: it powers and charges the mic and carries no audio. The VideoMic Pro runs on a 9 V battery and has no USB at all.
So a Pro or Pro+ reaches a Mac in one of two ways.
Route 1: a small 3.5 mm interface
RØDE's own answer is the AI-Micro, $89 in its US store as of October 2026. It is a two-input interface with 3.5 mm jacks that sense TRS or TRRS plugs automatically, records at 24-bit, 48 kHz, has a headphone output with direct monitoring, and comes with USB-A, USB-C and Lightning cables. RØDE's FAQ confirms it supplies plug-in power, which matters for the battery-free models below.
This is the reliable route. The Mac sees the AI-Micro as a USB audio device, the mic's analogue signal goes through the interface's preamp and converter rather than the Mac's, and it works the same on a MacBook Air, a Mac mini or a Mac Studio.
Route 2: the Mac's headphone jack with an adapter
Most Macs with a 3.5 mm port treat it as a headset jack. Apple's Mac User Guide says the port "supports stereo output and mono input (such as a headset with a built-in microphone)". A headset jack expects a four-contact TRRS plug, and a VideoMic ends in a three-contact TRS plug. RØDE's cable guide is blunt about it: plugging a TRS mic into a TRRS input generally has issues. The fix is RØDE's SC4, a $19 TRS-to-TRRS adapter, between the mic cable and the Mac.
It can work, with limits you should know before relying on it for calls:
- The Mac's jack input is mono and runs through the Mac's own analogue circuitry, which Apple does not specify for external mics.
- Apple does not publish how much plug-in power the jack supplies. The Pro and Pro+ carry their own batteries, so that does not matter for them; for the VideoMicro II and the original GO, which need plug-in power, it is a gamble.
- Gain is set in two places. RØDE's advice for cameras applies here too: drive the mic's own gain up (the Pro+ has three stages) and keep the device's input lower, rather than the other way round.
If you own a Pro+ and expect to use it at the desk every week, the AI-Micro costs less than a third of the mic and removes the guesswork.
VideoMicro II, the Rycote VideoMic and the original GO
These three follow the same rule as the Pro: 3.5 mm TRS out, nothing digital.
- VideoMicro II ($89) has no battery and depends on plug-in power. Use an interface that supplies it, such as the AI-Micro.
- VideoMic with the Rycote mount ($159) has a 9 V battery, so it powers itself and works through either route above.
- The original VideoMic GO now sits in RØDE's legacy products. It needs plug-in power, and its spec sheet lists 34 dBA of self-noise and a frequency range of 100 Hz to 16 kHz, against 15 dBA and 20 Hz to 20 kHz for the GO II. If you are choosing between the two, the GO II is the one with USB and the quieter capsule on paper.
VideoMic Me, Me-L and Me-C: phone mics
If you searched for the VideoMic Me, you found a phone accessory. The Me-L plugs into an iPhone's Lightning port and RØDE lists iOS as its requirement. The Me-C targets USB-C phones running Android 10 or later and has moved to RØDE's legacy list. The plain VideoMic Me uses a TRRS plug for phone headset jacks. None of them is sold as a Mac microphone, and on a Mac they have no advantage over the models above.
Setting a VideoMic up for a call on a Mac
Here is a working chain for the most common case, a VideoMic NTG on a desk for a Zoom or Google Meet call. The GO II version is the same, with the switches moved into RØDE Central.
Mic position: on a small tripod or boom, 20 to 30 cm from the mouth,
aimed at the mouth, NOT on the camera 60+ cm away
Cable: USB-C (SC16 from the box) into the Mac
VideoMic NTG: gain knob at 10 to start; HPF 75 Hz on; pad off
(pad on if the peak LED flashes red)
macOS: System Settings > Sound > Input > VideoMic NTG
Output > where your headphones are connected
(VideoMic NTG only if they plug into the mic)
Call app: pick VideoMic NTG as the microphone in the app's
audio settings
Monitoring: headphones into the NTG's 3.5 mm jack if you
want to hear yourself live
Check: record 30 s in QuickTime Player and listen back
on headphones before the call
The single most important line is the first one. A shotgun on top of a camera sits an arm's length away, and on a desk that distance is where most of its call quality goes.
What a camera shotgun gives you on a call
A VideoMic is a supercardioid shotgun. It is most sensitive straight ahead and less sensitive to the sides, and the range is built to sit on a camera, where the subject is usually a metre or more away. That is a fine job outdoors, where nothing reflects the sound back. Indoors, at a desk, the physics change: the side rejection of a short interference tube works mostly on high frequencies, and the reflections from a bare wall and a desk arrive at the capsule from the sides and the back. The farther the mic is from your mouth, the larger the share of room sound in the signal. Our article on whether a shotgun mic suits calls and streaming at a desk walks through that mechanism in detail.
In practice that gives three rules for a VideoMic on a Mac:
- Move it closer. Off the camera's cold shoe, onto a desk tripod or a boom, 20 to 30 cm from the mouth. A shotgun is built to keep a voice intelligible at a distance, and it still does better close. Halve the distance and your direct voice gets about 6 dB louder while the room's reverberation stays roughly where it was.
- Point it at your mouth, not your chest. The pattern is narrow on axis, and a few centimetres off the axis lose the top end of the voice first.
- Use the high-pass filter. At 75 Hz it removes rumble a call app would otherwise try to fight.
Then there is the processing on the Mac side, which is free:
- macOS Mic Mode. In apps that support it, Apple lets you pick Standard, Voice Isolation or Wide Spectrum from Control Center while the app is using the mic. Voice Isolation suppresses sound that is not speech.
- The call app's own suppression. Zoom, for example, has background noise suppression under Settings > Audio with Auto, Low, Medium and High levels.
Both work on any input, a VideoMic included. Both are built for the average voice and the average mic, and stacking them means two separate stages each guessing what counts as noise. If you stay in the same room with the same mic every day, it often makes more sense to set up that chain once, for that exact combination, than to lean on generic suppression in every app.
If you also record on the Mac
For voice-overs, narration for a video, or a podcast intro, the NTG and GO II behave like any USB mic: QuickTime Player, GarageBand or any editor will record from them. RØDE's apps add the filters and pad. The general workflow (levels, file formats, monitoring, cleaning up a take) is covered in our guide to recording audio on a Mac so your voice sounds good. The one VideoMic-specific point: in the GO II's case, settings changed in RØDE Central do not carry over when you plug the mic back into a camera, since 3.5 mm mode runs with fixed settings.
Where TunedMic fits
A VideoMic NTG or GO II on USB, or any VideoMic through an AI-Micro, gives the Mac a clean signal. What reaches the people on the call is that signal plus your room plus whatever the call app does to it. TunedMic works on that last stretch.
TunedMic is a Mac app that adds a virtual microphone, also called TunedMic, next to your real one. It takes the sound from the VideoMic, processes it on the Mac in real time, and every app you point at TunedMic (Zoom, Google Meet, Teams, Slack, Discord, OBS, FaceTime, browsers) hears the processed voice. Setting it up takes about a minute. Sound Check has you read a short passage with the VideoMic in its usual spot, and in that time TunedMic takes more than 30 measurements of your voice, this mic and your room, then builds its nine profiles from what it heard. Narrator Natural or Focused suit calls; the Creator profiles suit streams and videos. Switching profile changes the sound in every app at once. The delay it adds is under a tenth of a second.
Why that matters for a VideoMic specifically: a shotgun at 25 cm still hears more room than a close desk mic, and the right amount of cleanup depends on that room. Sound Check measures it instead of assuming it.
The limits, plainly:
- TunedMic needs a Mac with Apple silicon (M1 or newer) and macOS 14 or later. There is no Windows version and no Intel support.
- It does not change your voice into someone else's, and it does not turn a VideoMic on a camera two metres away into a close mic. Move the mic first.
- It costs $19 once, with a free 7-day trial that starts at first launch, includes every feature and needs no card or account. There are no refunds, so use the trial on your real VideoMic setup, in your real room.
The home page has a 38-second video of the setup, which comes down to reading aloud for a minute. There is no VideoMic in it, so how yours sounds is something only the trial on your own desk can tell you.
So, should you use a VideoMic as your Mac microphone?
- You own a VideoMic NTG or GO II: yes. Take it off the camera, put it on a small stand 20 to 30 cm from your mouth, plug in USB-C. That is a real desktop USB mic.
- You own a VideoMic Pro, Pro+, Rycote VideoMic or VideoMicro II: it works through an AI-Micro ($89) reliably, or through the headphone jack with an SC4 adapter if you accept the Mac's mono analogue input. If calls are your daily use, the interface is worth it.
- You are buying one mic for both camera and Mac: the NTG if you want controls on the mic and a battery; the GO II if you want the same USB route for $150 less. Skip the Pro+ for this job; its strengths are on a camera.
- You want a mic only for calls: a VideoMic is not the obvious buy. A close desk mic is simpler, and our best microphone for YouTube guide shows where a camera shotgun sits among the options.
Your next step takes five minutes. Plug the VideoMic in the way your model allows, select it in System Settings > Sound > Input, and record thirty seconds in QuickTime Player from the spot where you take calls. Listen on headphones. If the room is louder than your voice, move the mic closer before anything else. If the mic is close and you still hear the room, run the free 7-day TunedMic trial on that same setup; pricing is here when you decide.