Are the MXL 990, Behringer C-1 and XM8500 good enough for voice?

Yes, for calls, streams and a first podcast, but none of the three works alone. What the MXL 990, Behringer C-1 and XM8500 need on a Mac, how each handles an ordinary room, and which one to pick.


A Behringer XM8500 arrives in a plastic case with a stand clip, costs £16.70 at Thomann UK as of October 2026, and weighs about 240 g. You plug it into a Mac through a cheap USB interface, open Zoom, and the first thing anyone says is "you're really quiet." You drag the input slider to the top. Now people can hear you, and they can also hear a steady hiss that was never there with the laptop mic.

The mic did nothing wrong. The chain around it did.

That is the real answer to the question in the title. The MXL 990, the Behringer C-1 and the Behringer XM8500 can all carry a speaking voice well enough for calls, streams and a starter podcast. None of them does it on its own. Each needs something that is not in the box, and if that something is a Focusrite Scarlett Solo ($169.99 on Focusrite's site as of October 2026), it costs more than the microphone in all three cases.

This page sticks to those three models. If you have not narrowed it down yet and want the wider field of XLR mics in this price band, which XLR microphone is worth buying for a home setup compares them, and that is the better page for you. If you are not set on XLR at all and just want the cheapest mic that sounds decent, start with which budget microphone is worth buying instead.

The three mics side by side

The numbers below come from the makers' own spec sheets where they exist, and from an independent teardown where they do not. Prices are new, US or UK retail, as of October 2026.

MXL 990Behringer C-1Behringer XM8500
Typecondenser, cardioidcondenser, cardioiddynamic, cardioid
Needs 48 V phantom poweryesyesno
Output (sensitivity)15 mV/Pa22.4 mV/Pa"-70 dB", no reference given
Self-noise20 dB(A)not published by Behringernegligible (no electronics inside)
Frequency range20 Hz to 20 kHz40 Hz to 20 kHz50 Hz to 15 kHz
In the boxshock mount, hard mount, casestand mount, casestand clip, case
Price, Oct 2026about $84 to $90about $54 (stock is patchy)£16.70 at Thomann UK

Two of these are condensers that will hear your whole room. One is a dynamic that hears mostly what is right in front of it and asks for a lot of preamp gain in return. That split matters more for a speaking voice than any line in the table.

MXL 990: the condenser that hears everything

MXL's own page lists the 990 as a pressure-gradient condenser with a 6-micron gold-sputtered capsule, cardioid pattern, 20 Hz to 20 kHz, 15 mV/Pa sensitivity and an equivalent noise level of 20 dB A-weighted. It needs 48 V phantom power. The box includes a shock mount, a hard mount and a carrying case, which is more hardware than you get with either Behringer.

The 15 mV/Pa figure is the part to understand. It means the 990 turns sound into a strong electrical signal, so it needs little preamp gain. Sensitivity alone does not decide how much of the room you hear; distance does. But a hot condenser invites you to sit back from it, and at 30 to 40 cm it turns everything else into signal too: the fridge, the keyboard, the hum of a laptop fan, the reflection of your own voice off the wall behind the monitor. A review on Home DJ Studio describes the 990 as bright, with a gentle lift around 8 kHz, and calls its 20 dB(A) self-noise "on the higher end." For normal speech that hiss sits well under your voice. For whisper-quiet voice-over in a silent room, it is the first thing you would upgrade away from.

Where the 990 works for voice: a quiet, soft-furnished room, the mic 15 to 20 cm from your mouth, a pop filter in front. Where it struggles: a bare room with a hard floor, a mechanical keyboard on the same desk, or a street outside the window. In that second room it is not a bad mic. It is an accurate one.

MXL has also sold a USB version of this mic, listed by retailers as the MXL 990 USB. If you want this capsule without an interface, check whether a shop near you still has it in stock before planning around it.

Behringer C-1: cheaper, and smaller inside than the name suggests

People search for this one as both "Behringer C1" and "Behringer C-1". It is the same mic. Behringer and its retailers market it as a large-diaphragm condenser with a 16 mm capsule, 40 Hz to 20 kHz response, 136 dB maximum SPL and an LED that lights when phantom power arrives.

An independent teardown on Recording Hacks tells a more specific story. The capsule is a small-diameter electret mounted behind a perforated plate; its housing measures 17.2 mm across, so the diaphragm itself is presumably 10 to 14 mm. The circuit is a single JFET (a Fairchild J202). The same page lists 22.4 mV/Pa sensitivity, which is even hotter than the MXL. In a signal-injection test the response was flat from 20 Hz to 2 kHz, then rose gently to about +1 dB at 10 kHz and +2 dB at 20 kHz.

None of that makes the C-1 unusable. A flat response with a small lift on top is a reasonable shape for speech. It does mean you should not expect it to behave like a real large-diaphragm studio condenser, and like the 990 it will pick up the room whenever it is used at a distance.

The bigger issue in October 2026 is buying one. Equipboard showed it at $53.90 new on Amazon and B&H on October 10, 2026, but at least two UK retailers mark it discontinued and its Thomann UK page now returns a 404. If you find one new at that price, fine. If not, do not pay a scalper's premium for it.

There is also the C-1U, a USB version. Recording Hacks lists its converter as 16-bit, 44.1 kHz and notes there is no headphone jack, so you cannot hear yourself through the mic. It plugs straight into a Mac with no interface, which makes it the simplest way to get this capsule onto a call.

Behringer XM8500: the dynamic that needs gain

Behringer's own spec sheet for the Ultravoice XM8500 lists a cardioid dynamic capsule, 150 ohm impedance, 50 Hz to 15 kHz bandwidth, about 240 g, an integrated wind and pop filter, and "a smooth mid-frequency presence rise for excellent voice projection." It needs no phantom power, because a dynamic mic has no electronics inside: a coil moves in a magnet and that movement is the signal.

The sheet gives sensitivity as "-70 dB" without saying what that is relative to, so it cannot be compared directly with anything else. A useful reference point is the Shure SM58, the dynamic most people know, which Shure rates at 1.85 mV/Pa. Compared with the MXL 990's 15 mV/Pa, that is about 18 dB less signal for the same voice. Behringer's sheet calls the XM8500's output "extremely high" but gives no figure that would set it apart from other moving-coil mics, so plan for SM58-class output. That gap is what produced "you're really quiet" in the opening scene.

The gap has to be made up somewhere. Either the interface's preamp supplies it, or an inline booster such as a Cloudlifter does (the Cloudlifter and FetHead guide covers when that is worth it). Cranking the macOS input slider instead does not add clean gain; it amplifies whatever the preamp already let through, hiss included.

Here is the trade that makes the XM8500 interesting for voice. It is built to be used up close, and its cardioid pattern rejects sound from behind, so in practice it hears far less of your room. Speak 5 to 10 cm from the grille and your voice arrives far louder than the fridge three metres away. For calls from an ordinary bedroom or a shared flat, that is worth more than the condensers' extra detail.

What each one needs before it makes a sound on a Mac

None of the three XLR versions plugs into a Mac directly. Here is the full chain for each:

XM8500   -> XLR cable -> interface (no phantom needed, plenty of gain) -> USB -> Mac
C-1      -> XLR cable -> interface with 48 V phantom ON              -> USB -> Mac
MXL 990  -> XLR cable -> interface with 48 V phantom ON              -> USB -> Mac
C-1U     -> USB cable -> Mac (16-bit / 44.1 kHz converter inside the mic)

Any USB interface that sends 48 V phantom power covers the two condensers. Behringer's own UM2 has one XLR combo input and switchable +48 V phantom. The Focusrite Scarlett Solo 4th Gen offers 57 dB of mic gain, phantom power and Apple silicon support, at $169.99. For the XM8500, the number that matters is how much clean gain the preamp has, because you will use most of it.

If you were hoping to skip the interface with a single XLR-to-USB cable, read whether an XLR mic plugs into a Mac with a USB adapter before ordering one: the short version is that a condenser needs an adapter that actually supplies phantom power, and a dynamic needs one with enough gain. Our page on phantom power explains what the 48 V does and why the XM8500 does not care about it.

So the honest budget for each mic is the mic plus an interface, a cable, a stand and a pop filter. On that math the XM8500 stops being a £17 microphone and becomes a setup that costs several times that.

Condenser or dynamic, in the room you actually have

The reason the type matters so much for voice is distance. Sound from your mouth falls off quickly with distance: each time you halve the gap between mouth and mic, your voice gets about 6 dB louder relative to the room around you. A dynamic used at 5 cm gets that advantage several times over. A condenser used at arm's length gets none of it.

That is why the same pair of mics can trade places depending on the room:

  • Quiet room, soft surfaces, you sit still: the MXL 990 or C-1 at 15 to 20 cm will capture more of the air and detail in your voice than the XM8500.
  • Ordinary room, hard walls, some background noise: the XM8500 at 5 to 10 cm will usually give the cleaner call, because it is working with a much better voice-to-room ratio.
  • You move around while you talk: a condenser forgives movement better, a dynamic punishes it. Lean back 20 cm from an XM8500 and your level falls off sharply.

The longer explanation of this choice lives in whether a dynamic or a condenser mic is better for a normal room. For these three specifically, the takeaway is short: in a normal room, the cheapest mic of the three is the best fit for speech.

Where a cheap mic loses to bad setup

Most complaints about these mics are setup problems wearing a mic's name. The checklist below lists what to get right before you blame the capsule.

CheckXM8500MXL 990 / C-1
Phantom poweroff (not needed)on, 48 V, LED lit on the C-1
Mouth to grille5 to 10 cm15 to 20 cm
Speak intothe top of the grillethe front face of the body (side-address)
Preamp gainhigh, most of the rangelow to mid
Speech peaks on the interface meterwell short of the red clip lightsame
macOS input sliderleave near default once preamp gain is rightsame
Pop filterbuilt into the grilleadd one

Three of these cause most of the trouble.

Gain set in the wrong place. The preamp knob on the interface sets how much clean signal you get. The input slider in System Settings > Sound > Input only scales what already arrived. If the voice is quiet, turn the knob first. A clipped signal (red light) cannot be repaired later by anything, so leave headroom. Our gain staging guide walks through it.

Talking into the wrong side. The MXL 990 and C-1 are side-address: you speak into the front face of the body (on the 990, the side with the logo), not the top. Speaking into the end cap of a side-address mic puts you off-axis, which costs level and treble. The XM8500 is the opposite: aim for the top of the ball.

Distance drift. A condenser on a desk stand at 40 cm sounds roomy and thin no matter which one you bought. Get it closer with a stand or boom arm before blaming the capsule.

Fix those three and most of the "cheap mic" sound goes away. What is left is the room and the shape of your own voice, and that is where software starts to earn its place.

What software can and cannot do after the mic

Start with what is free. macOS lets you pick the input and its level under Apple menu > System Settings > Sound > Input. Zoom, Teams, Discord and most other call apps have their own noise suppression, and for a steady fan in the background it is often enough. If you record rather than call, a free editor can apply EQ and compression afterwards.

What those tools do not do is tune the sound to you. App noise suppression removes noise; it does not decide that your voice needs less boom at 200 Hz through an XM8500 or less edge around 8 kHz through a bright condenser. A fixed EQ preset copied from a forum was made for someone else's voice in someone else's room.

That is the gap TunedMic was built for, on a Mac. It adds a virtual microphone called TunedMic to macOS; your real mic, or the interface it is plugged into, stays as it is. During a one-minute Sound Check you read a short passage aloud and the app takes more than 30 measurements of your voice, your mic and your room. From that it builds nine profiles (Natural, Warm and Focused for calls, three for creators, three for singing), and Zoom, Meet, Telegram, Discord or OBS pick up the result when you select TunedMic as their mic. Noise, room echo, clarity, loudness and a 12-band equaliser are there if you want to adjust by hand. The added delay is under a tenth of a second, and the processing stays on the Mac.

Its limits are worth stating plainly. It needs a Mac with Apple silicon (M1 or newer) and macOS 14 or later; there is no Windows or Intel version. It processes what arrives, so it cannot un-clip a signal your preamp already distorted, and it will not make an XM8500 into a different microphone. It also will not remove every noise in every room. What it changes is how your voice sits on top of the mic you already chose.

Which one to buy, if it has to be one of these three

For calls and streams in an ordinary room: the XM8500. It hears the least of your room, it needs no phantom power, and it leaves the most money for the interface, which is the part that decides whether it sounds clean. Budget for a preamp with real gain and speak close.

For voice-over or reading in a quiet, soft room: the MXL 990. It comes with a shock mount, it is easy to find new, and its extra detail is real when the room is not fighting it. Use a pop filter and keep it at 15 to 20 cm.

The C-1 only if you find it new at its old price, or if you want the USB C-1U. It is a reasonable small condenser that is marketed as something bigger, and in October 2026 its stock is unreliable.

If none of the three fits because you would rather not buy an interface at all, that is a sign a USB mic is the better buy, and the budget mic guide is the page for that.

Before you spend anything

Record thirty seconds of your normal speaking voice with the mic you have now, in the room where you will use the new one, and play it back on headphones. If the problem you hear is the room (echo, fan, street), an XLR condenser will make it louder, and the XM8500 or better placement is the fix. If the problem is the voice itself sounding thin, boomy or harsh, the mic matters less than how it is tuned.

To see what tuning asks of you, watch the 38-second video on the home page: a minute of reading aloud, then a Speech Report after each call. What it does on cheap hardware you will only hear on yours. TunedMic has a free 7-day trial that starts at first launch, with every feature available and no card or account; after that it is $19 once, as listed on the pricing page. Note that payments are final, so use the seven days on the mic you actually own.

Keep reading