Is the Audio-Technica ATR2100x still a good budget podcast mic?

Audio-Technica now marks the ATR2100x-USB as discontinued in the US. How it compares with the older ATR2100 and the Samson Q2U, how to set it up on a Mac, and when a used one is still a smart buy.


The ATR2100x-USB manual has one line that explains a lot of confused evenings: when you connect to a USB-C port, "you must use a USB On-The-Go (USB OTG) cable like the one included." Lose that cable, plug the mic into a MacBook with a random USB-C cable from the drawer, and if nothing appears under System Settings > Sound > Input, the cable is the first suspect, not the mic. Swap back to the cable from the box before you blame anything else.

That small trap says a lot about where this microphone stands in 2026. Its manual comes from another era of the Mac: the setup pages still walk you through System Preferences on macOS Mojave, with a warning about Catalina. The mic still does the job it was designed for. And fewer people know its quirks every year, because fewer people can buy one new.

The short answer: is the ATR2100x still worth it?

Yes as a design. Not always as a purchase.

The ATR2100x-USB is a handheld dynamic cardioid mic with two outputs, USB-C and XLR, a headphone jack with its own volume dial, and a desk tripod in the box. That combination is still exactly what a first podcast mic should have: plug it straight into the Mac today, move it to an audio interface later without buying another mic. Nothing about recording speech has changed in a way that makes that formula obsolete.

What changed is the shelf. As of October 2026, Audio-Technica's US site marks the ATR2100x-USB as discontinued, and Sweetwater lists it as unavailable. Audio-Technica's UK store still lists it at £79.99. So the verdict splits three ways:

  • You already own one. Keep it. Nothing in the same price range changes your recordings as much as fixing distance and level does.
  • You can get one new or lightly used near its old price. Good buy, with the cable caveat above.
  • You are in the US and can only find it at collector prices. Skip it and buy the closest twin that is still made.

That twin is the Samson Q2U. If you have already ruled out a discontinued mic and only want to know whether the Q2U holds up, the Samson Q2U breakdown is the page for you instead of this one.

ATR2100 vs ATR2100x: which one are you looking at?

Search for "atr2100" and you get two microphones under nearly one name. The older ATR2100-USB is the one podcast guides recommended for years. The ATR2100x-USB replaced it. Both are now marked discontinued on Audio-Technica's US site, both still circulate secondhand, and listings mix them up constantly.

ATR2100-USB (older)ATR2100x-USBSamson Q2U (current)
CapsuleDynamic, cardioidDynamic, cardioidDynamic, cardioid
Published frequency range50 Hz to 15 kHz50 Hz to 15 kHz50 Hz to 15 kHz
USB portMini USBUSB-CUSB-C
USB resolution16-bit, 44.1/48 kHzup to 24-bit, up to 192 kHzup to 16-bit, 44.1/48 kHz
XLR outputYesYesYes
Headphone jack with volumeYesYesYes (3.5 mm)
Weight268 g268 g320 g
In the boxTripod, clamp, mini USB cable, XLR cableTripod, clamp, USB-C to USB-C (OTG) and USB-C to USB-A cables, 3 m XLR cableClip, tripod with extension, foam windscreen, USB cable, 3 m XLR cable
Status, October 2026Discontinued (A-T US)Discontinued (A-T US), £79.99 on A-T UK store$99.99 list on Samson's store

The fastest way to tell the two Audio-Technica models apart in a listing photo is the port on the bottom. Mini USB means the older mic. USB-C means the x.

Look at what the table does not change: same capsule type, same pickup pattern, same published range, same weight. The x update was about the digital side, a newer connector and a converter that goes to 24-bit. For a speaking voice, 24-bit at 48 kHz is plenty, and the 192 kHz option buys nothing a podcast can use; the sample rate and bit depth guide explains why. The 24-bit part does help a little: you can set a cautious level, leave headroom for laughter, and the quiet parts still sit well above the converter's own noise.

So an old ATR2100-USB with its mini USB cable is not a worse microphone for voice. It is an older plug. If one turns up cheap with the cable, it is a reasonable buy, as long as you pay older-model money for it.

Why a dynamic USB/XLR mic is still the right shape

The ATR2100x earned its reputation for reasons that have little to do with Audio-Technica specifically. A dynamic capsule wants your mouth close, about a hand's width, and in exchange it hears much less of the room: the fridge, the echo off a bare wall, the keyboard. Most people starting a podcast record in a bedroom or a home office, so the mic that hears less of the room is the safer bet. Whether a dynamic mic really is better in a normal room gets its own page, including the cases where it is not.

The dual output matters for a different reason: money spent over time. Over USB you need nothing else. When the show becomes two people in one room, or you want a proper preamp, the same mic goes into an interface over XLR. Audio-Technica confirms in its product Q&A that the ATR2100x does not need phantom power on XLR, so any mic input works.

One thing to understand before planning that move. Over XLR, the computer sees the interface, not the microphone. Audio-Technica's support answer puts it plainly: with XLR into an interface, the computer recognizes the interface and registers no USB signal from the mic. The manual describes the mic's headphone jack as working while the mic is connected over USB with the blue LED lit, so with XLR alone your monitoring moves to the interface's headphone output. If you are weighing an adapter instead of an interface, read whether a USB adapter can run an XLR mic on a Mac first.

ATR2100x vs Samson Q2U

These two were always compared, and on paper they are close: same capsule type, same pattern, the same published 50 Hz to 15 kHz, both with USB-C, XLR, a headphone jack and an on/off switch. The differences are smaller than the forum arguments suggest.

  • USB resolution. The ATR2100x goes to 24-bit; the Q2U tops out at 16-bit, 44.1 or 48 kHz. Set to a sensible level, both are fine for speech. The 24-bit converter is more forgiving if you set your level low.
  • What is in the box. The Q2U includes a foam windscreen. The ATR2100x does not, and on a mic you talk into from a few centimetres, the "p" and "b" bursts are a real problem. A foam cover or a pop filter costs very little.
  • Paper sensitivity. Samson publishes -54 dBV/Pa for the Q2U. The specifications on Audio-Technica's ATR2100x page have no sensitivity line, so you cannot compare on paper how much preamp gain each one needs over XLR.
  • Availability. This is the row that decides it. The Q2U is still on Samson's store at $99.99 list. In the US, an ATR2100x is leftover stock or used.

If you can get either at a similar price, it is close to a coin toss: pick by what comes in the box. If only one is available new, take that one.

How to set up the ATR2100x on a Mac

There is no driver and no companion app. The mic is a standard USB audio device and macOS sees it directly. Nearly every problem comes from three places: the cable, the level and the switch.

ATR2100x-USB on a Mac, USB mode

Cable       USB-C to USB-C from the box (OTG), or USB-C to USB-A plus adapter
Input       Apple menu > System Settings > Sound > Input > ATR2100x-USB
Output      check the Output tab: macOS may switch to the mic's headphone jack
Level       Input volume slider: start around 75%, talk at full voice,
            loudest peaks stay clear of the top of the meter
Distance    5 to 15 cm, on axis, mouth aimed at the end of the grille
Plosives    angle the mic slightly off your mouth line, or add foam
Monitoring  headphones into the mic's 3.5 mm jack; the dial is headphone volume only
Switch      the on/off switch silences the mic; the blue LED stays lit either way

A few of those lines need more room.

The level lives in macOS, not on the mic. The dial on the bottom looks like a gain knob. The manual says plainly that it changes only headphone volume. If your recording is quiet, raise the input slider in Sound settings or in the recording app. Why a mic ends up too quiet walks through the rest of the chain.

The LED does not tell you whether you are live. Audio-Technica's manual notes that the on/off switch does not affect the LED. Mid-recording, a lit blue light only means the mic has USB power. Trust the meter, not the light.

Distance does more than any setting. A dynamic mic rewards being close. At a hand's width your voice is far louder than the room, and a moderate slider position gives a solid level. Lean back to arm's length and you need more gain, and the room comes up together with your voice. Being close also adds low end, the proximity effect, which is part of why radio presenters work so near the mic.

The tripod is the weak part. Owner reviews on Audio-Technica's own product page include complaints about the included plastic tripod. If you move to a boom arm, Audio-Technica's support answer says the AT8415 shock mount fits this mic, while the smaller AT8410a does not.

Where the ATR2100x falls short

Its weak points are the ones most plain USB dynamic mics share, and you should know them before you pay.

No processing at all. The ATR2100x hands the Mac a raw signal: no compressor, no high-pass filter, no noise reduction. Some newer mics in the same broad class do that work inside the mic. RODE's PodMic USB, for example, has on-board DSP with APHEX processing and works with RODE's software. Whether you care depends on where the audio goes. A podcast you edit afterward can get compression and EQ in the editor. A live call or a stream cannot be edited afterward.

No hardware gain, no proper mute. Gain is a software slider, and the mute is a slide switch with no indicator. Fine on a desk, clumsy live.

On calls, the app decides. Plenty of people use their ATR2100x for work calls too. Zoom, Google Meet or Discord then apply their own processing, built for every voice at once and blind to yours, your mic and your room. macOS Mic Modes such as Voice Isolation exist only in apps that support them, FaceTime among them, and the options vary by app.

None of this is a reason to skip it. It is simply what the mic is: a decent capsule, a clean converter and nothing else.

Where TunedMic fits, and where it does not

If you only record a podcast and edit it afterward, you can handle the "nothing else" part in your editor and you need no extra software. TunedMic is for the other case: your ATR2100x is also the mic you talk into live, on calls, streams, Discord sessions or an interview recorded straight from a call, where nothing gets fixed later.

TunedMic is a Mac app that adds a virtual microphone next to your real one. You run a one-minute Sound Check, reading a short passage aloud while the app takes more than 30 measurements of your voice, your mic and your room. Then any app that lets you choose a mic, whether Zoom, Discord, OBS, Telegram, FaceTime or a browser, can pick TunedMic and hears the processed voice. The three Creator profiles (Balanced, Broadcast, Crisp) are meant for streams, videos and podcasts, and each one is built from your own Sound Check rather than a stock preset. If you want to go further, there are manual controls for noise, room echo, clarity, loudness and a 12-band EQ, though you never have to touch them. It adds less than a tenth of a second of delay and runs on the Mac; your voice is not uploaded.

What it does not do: turn the ATR2100x into a specific expensive microphone, or remove all noise in every room. It also has hard limits. It needs a Mac with Apple silicon (M1 or newer) and macOS 14 or later. There is no Windows version and no Intel support, so if your ATR2100x lives on a gaming PC, this is not your fix.

The 38-second video on the home page shows how TunedMic is set up, not how an ATR2100x sounds: the one-minute Sound Check, TunedMic picked as the mic in Zoom, Google Meet and Discord, and the Speech Report afterwards. How your own ATR2100x sounds through TunedMic is what the free 7-day trial below is for.

Alternatives still on sale

If you cannot find an ATR2100x at a sensible price, these are the realistic options as of October 2026:

  • Samson Q2U, $99.99 list. The nearest twin: handheld dynamic, USB-C and XLR, headphone out, windscreen in the box. For anyone who wants the ATR2100x formula as a current product.
  • Fifine AmpliGame AM8, $57.99 on Fifine's store. A cheaper USB/XLR dynamic mic. For a tight budget; see whether Fifine and Maono mics are good enough.
  • Maono PD200X, $89.99 on Maono's US store (that listing includes a boom arm). A USB/XLR dynamic mic in the broadcast shape; details in the PD200X review.
  • Audio-Technica AT2040USB, $159 on A-T's US store. The brand's current dynamic USB mic: hypercardioid, with low cut, mute and a monitor mix control. It has no XLR output, and Audio-Technica's OS list stops at macOS Ventura. For someone certain they will never want XLR.

If you are still choosing your very first mic and the ATR2100x was simply the name you had heard, the beginner's guide to podcast mics compares the field and covers what else you need to start.

Buying a used ATR2100x: a ten-minute check

Used ATR2100x and ATR2100 units turn up regularly on marketplaces such as eBay. Before you pay:

  1. Ask whether the USB-C to USB-C cable from the box is included. If not, buy an OTG-compliant cable or use USB-C to USB-A with an adapter.
  2. Plug it in over USB. The blue LED should light, and the mic should appear in Sound > Input.
  3. Talk with the on/off switch in both positions. The meter should move only with the switch on.
  4. Plug headphones into the mic, turn the dial both ways, and listen for crackle as it turns.
  5. Shake it gently next to your ear. A rattle inside a handheld mic is a bad sign.
  6. If the listing says ATR2100 without the x, check the port. Mini USB means the older 16-bit model: fine for voice, worth less money.

What to do next

If you already own an ATR2100x, spend five minutes before you spend any money. Move it to a hand's width from your mouth, set the input slider so your loudest laugh stays out of the top of the meter, and use the OTG cable from the box if the Mac ever stops seeing the mic. Record thirty seconds in QuickTime and play it back on headphones.

If the result is clean but flat on live calls and you have an Apple silicon Mac, run the free 7-day trial with your own ATR2100x as the input: it starts at first launch, opens every feature and asks for no card or account. After seven days the app locks until you enter a license, $19 one-time on the pricing page. There are no refunds, which is exactly why the trial comes first.

Keep reading