Which Audio-Technica mic should you buy, the AT2020 or the AT2035?
The AT2035 costs $70 more than the XLR AT2020. What that buys: an 80 Hz filter, a 10 dB pad, a shock mount, 4 dB more output and 8 dB less self-noise. Who needs it, and what both need on a Mac.
Two tabs are open. In one, the Audio-Technica AT2020 for $88. In the other, the AT2035 for $158. Both prices are from Thomann's international store as of October 2026, and both mics are cardioid, side-address condensers with an XLR plug at the bottom and the same "20 Hz to 20 kHz" printed in the specs. The product pages do a poor job of explaining what the extra $70 buys. The short version: two switches on the body, a shock mount in the box, and two spec-sheet lines that most comparisons skip.
This page is about the XLR mics: the AT2020 XLR and the AT2035, which only comes as XLR. If you are looking at the AT2020 that plugs straight into a USB port, that is a different purchase with no interface involved, and our AT2020 USB article is the page you want. If you are not yet sure a condenser belongs in your room at all, read what a condenser microphone is and when it suits a room first, because everything that page says applies to both mics here.
The short answer: AT2020 vs AT2035
For someone who talks on a Mac at a desk (calls, lessons, podcasts, voice-over), the AT2035 mic is the better buy, and the larger diaphragm is not the reason. The reason is that it handles two everyday problems the AT2020 leaves to you: low rumble and desk knocks. The 80 Hz filter and the shock mount deal with both before the sound ever reaches the Mac.
The AT2020 wins in three cases:
- the budget is fixed and the $70 would otherwise come out of the audio interface;
- the mic will live on a boom arm or a floor stand that does not touch the desk you type on;
- you record mostly in an editor, where a low-cut filter is one click away anyway.
What neither mic changes is your room. Both are condensers, both hear the walls around you, and an AT2035 in a bare room with a hard floor will sound more like the room than an AT2020 in a room with a sofa, curtains and a full bookcase.
The spec sheet side by side
Here are the manufacturer's numbers for the Audio-Technica AT2020 and the Audio-Technica AT2035, plus what each one ships with.
| AT2020 | AT2035 | |
|---|---|---|
| Type | Cardioid condenser, side-address | Cardioid large-diaphragm condenser, side-address |
| Diaphragm | 16 mm, low-mass | Large diaphragm |
| Frequency response | 20 Hz to 20 kHz | 20 Hz to 20 kHz |
| Sensitivity | -37 dB (14.1 mV) | -33 dB (22.4 mV) |
| Self-noise | 20 dB SPL | 12 dB SPL |
| Signal-to-noise | 74 dB | 82 dB |
| Max SPL | 144 dB | 148 dB, 158 dB with pad |
| Low-cut filter | None | 80 Hz, 12 dB/octave, switchable |
| Pad | None | 10 dB, switchable |
| Phantom power | 48 V, 2 mA | 11 to 52 V, 3.8 mA |
| Mount in the box | Pivoting threaded stand mount | AT8458 shock mount |
| Weight | 345 g | 403 g |
| Price, Thomann, October 2026 | $88 | $158 |
The frequency response line is identical, which is why so many comparisons stop there and call it a draw. The useful differences sit lower in the table: sensitivity, self-noise, the two switches and the mount.
Two numbers that matter more than they look
Sensitivity: about 4 dB less gain on the AT2035
Sensitivity is how much voltage a mic sends out for a given sound pressure. The AT2035 is rated at -33 dB and the AT2020 at -37 dB, so for the same voice at the same distance the AT2035 delivers about 4 dB more signal to the interface. You turn the gain knob 4 dB less to reach the same level.
That sounds small, and for a loud singer it is. For a quiet talker sitting 30 cm back from the mic it matters, because small interfaces get noisier as you push the preamp toward the top of its range. Every decibel you do not have to add there is hiss you never record. If you speak softly and your interface is a budget one, this line alone is a reason to prefer the AT2035.
Self-noise: 12 against 20 dB SPL
Self-noise is the hiss the mic's own electronics produce in a perfectly silent room. The AT2035 is 8 dB quieter on paper, and the signal-to-noise figures (82 against 74 dB) say the same thing from the other side.
Whether you ever hear that difference depends on the room, not the mic. If you can hear a laptop fan, a fridge, a radiator or the street while you sit still, that background is louder than either mic's hiss, and it will cover the difference completely. The 8 dB shows up in a quiet room with a quiet source and a lot of gain: whispered voice-over, ASMR, soft acoustic guitar, a narrator recording audiobook chapters late at night. For Zoom calls in a normal flat, it is not what you will notice.
The two switches the AT2020 does not have
The 80 Hz low-cut filter
Flip it and the AT2035 starts rolling off below 80 Hz at 12 dB per octave: about 12 dB down at 40 Hz and about 24 dB down at 20 Hz. Down there lives most of what is not voice. Footsteps through the floor, a fist hitting the desk, the hum of a ventilation system, trucks outside, the boom that builds up when you lean in close to a cardioid mic (the proximity effect).
On the AT2020 none of that is filtered at the mic. In a recording app or editor you add a high-pass filter yourself, and that works fine for files. On a live call there is no editor in the chain, so the filtering has to happen before the call app gets the sound: on the mic, on the interface if it has a low-cut button, or in a virtual microphone sitting between the interface and the app. If your voice is very deep, flip the filter, listen on headphones, and check that the chest of your voice has not thinned out. For most speaking voices it stays on.
The 10 dB pad
The pad lowers the signal inside the mic before its own electronics can overload. The AT2035 handles 148 dB SPL without it and 158 dB with it. Speech at a desk never comes close to either number, so for calls and podcasts leave the pad off. It earns its place in front of a guitar amp, a kick drum, or a singer belting a few centimeters from the grille.
Do not confuse the pad with interface clipping. If the meter on your interface hits red while you talk, the fix is less gain on the interface, not the pad. Our gain staging guide walks through setting levels so the loudest laugh still has room.
Shock mount against stand mount
The AT2020 ships with a pivoting threaded stand mount: the mic body screws onto something rigid that screws onto your stand. Anything the stand feels, the mic hears. If the stand is clamped to the desk you type on, every keystroke and every mug set down travels up the metal as a low thud.
The AT2035 comes with the AT8458 shock mount, which hangs the mic in elastic bands. It does not stop sound coming through the air, but it cuts the vibration coming through the stand. On a desk clamp, this is the most practical difference between the two mics, and it ties back to the filter: the shock mount stops most knocks, the 80 Hz filter cleans up the rest.
You can buy a shock mount for the AT2020 separately, and many people do. Once you add it, the price gap narrows, and you still have no filter or pad. If you already own a boom arm that does not touch your typing desk, the AT2020's rigid mount is far less of a problem.
What both mics hear: the room
Both are cardioid condensers. They are most sensitive at the front and less at the back, but a condenser is built to capture detail, and detail includes the reflections from the wall behind you, the window beside you and the bare ceiling above. Neither the larger diaphragm nor the lower self-noise of the AT2035 reduces room echo.
If your room is bare and loud, there is a fair argument for a dynamic mic instead of either of these, and our dynamic vs condenser comparison makes it in full. If you stay with a condenser, the cheapest improvement is distance: speak 15 to 20 cm from the grille instead of 50, so your voice is louder relative to the room, and put soft things behind you rather than in front.
What the XLR AT2020 or AT2035 needs on a Mac
A Mac has no XLR input. Neither mic has a USB port. Between them sits an audio interface, and both mics need phantom power from it to work at all. A condenser without phantom power is silent, not quiet.
Here is the whole chain, top to bottom:
AT2020 or AT2035
XLR cable, female end into the mic
USB audio interface
input gain: speaking peaks around -12 dBFS
48 V phantom power: ON (both mics need it)
AT2035 only: 80 Hz filter on, pad off for speech
Mac with USB-C or USB-A
System Settings > Sound > Input: choose the interface
Audio MIDI Setup > Format: 48 kHz for video and calls
Zoom, Telegram, Discord, OBS
microphone: the interface (or TunedMic, see below)
A few things trip people up on this route:
- Phantom power is off by default on many interfaces. The mic shows no signal until you press the 48 V button. See what phantom power is and which mics need it.
- Passive XLR-to-USB cables do not supply phantom power. Some active adapters do (Shure's MVX2U, for example, lists 48 V phantom power), and the spec sheet will say so. Read whether an XLR mic can go into a Mac through a USB adapter before you choose that route.
- Current draw. The AT2035 draws 3.8 mA and the AT2020 2 mA. A proper interface phantom supply is built for that; the risk is a cheap adapter running from a weak USB port.
- The Mac's input slider in System Settings is not where you set the level. The gain knob on the interface sets how much signal reaches its converter, so fix a weak or clipping voice there first.
Choosing the interface itself is a separate decision with its own trade-offs. Do you need an audio interface for a mic on a Mac covers why and what kind, and our comparison of MOTU M2, Audient iD4, SSL2 and PreSonus picks between specific small boxes. The sample rate setting is explained in our Audio MIDI Setup guide.
Budget for this chain honestly. The mic is the cheapest box in it: an XLR AT2020 at $88 still needs an interface and a cable before it makes a sound, and that spend is the same whichever of the two mics you pick.
Which one for which reader
Buy the AT2035 if:
- the mic clamps to the same desk you type on;
- you speak softly, or you record voice-over and audiobooks in a quiet room late at night;
- you want low rumble cut before it reaches any app, calls included;
- you sing loud and close and may need the pad.
Buy the AT2020 if:
- the $70 difference would otherwise come out of the interface;
- the mic sits on a floor stand or a boom arm that does not touch your desk;
- you record into an editor and are happy to add a high-pass filter there.
Buy neither if your room is bare, echoes when you clap, and you will not change that. A dynamic mic suits that room better, and our XLR buying guide lists options for it. And if what you actually want is one cable and no interface, go back to the AT2020 USB article.
One tuned mic for every app
Once the interface is plugged in, the Mac sees one input, and every app does its own thing with it. Zoom and Discord each run their own noise suppression, OBS has its own filter stack, and none of them knows what your room or your mic sound like. You end up tuning the same voice once per app, or not at all.
TunedMic is a Mac app that sits in exactly that gap. It adds one more microphone, called TunedMic, built from the interface's input. Setup is Sound Check: you read a short passage for about a minute while it takes more than 30 measurements of your voice, your mic and your room. Then you choose TunedMic once in Zoom, Google Meet, Telegram, Discord or OBS, and every app gets the same processed voice. Switching between its nine profiles changes the sound everywhere at once. The added delay is under a tenth of a second, it runs on the Mac and your voice is never uploaded. Manual controls for noise, room echo, clarity, loudness and a 12-band equalizer are there if you want them, and you never have to touch them.
The limits are real. TunedMic needs a Mac with Apple silicon (M1 or newer) and macOS 14 or later. There is no Windows version and no Intel support. It reduces noise and room echo but does not remove every sound, and it will not make an AT2020 sound like an AT2035 or either of them like a mic three times the price. The 38-second video on the home page shows the setup, the minute of reading aloud and the Speech Report at the end of a call; it does not show an Audio-Technica.
The price is $19 once, with a free 7-day trial that starts at first launch, includes every feature and needs no card or account. There are no refunds, so use those seven days on the mic you actually bought, and check pricing when you are ready.
Before you order
Go to the exact spot where the mic will live and answer two questions. Will its stand touch the desk you type on? Can you hear a fan, a fridge or the street while you sit still? If the stand touches the desk, order the AT2035 and use its shock mount and 80 Hz filter from day one. If it does not and the room is noisy anyway, order the AT2020 and put the $70 toward the interface. Either way, confirm that the interface you are buying has a 48 V phantom power button before you check out, because without it neither mic will make a sound.